Как запустить скрипт имея аппаратный доступ к терминалу?

[kamyaruk]

Есть камера V380pro Hw_EV2X_NA1_XHR_E_V1.0_WF_20250804 на прошивке V2.1.6.0(HSC_A2X1EXHR_20250804. На плате имеются пятаки Rx и Tx. подпаялся к ним и получил доступ к консоли.

CORE: 400(Mhz) VCLK: 200(Mhz)

U-Boot 2019.10.0-V4.0.25 (Aug 04 2025 - 16:47:03 +0800)

ASIC PLL: 400MHz
Model: S200W_EVB_CBD_AK3918EV201_V1.0.0
DRAM: 32 MiB
CORE: 400(Mhz) VCLK: 200(Mhz)
Flash: SF: Detected P25Q32SH with page size 256 Bytes, erase size 4 KiB, total 4 MiB
4 MiB
MMC: @get_card_status, card PLUGED
mmc0@20100000: 0
Loading Environment from SPI Flash... OK
[init_mvspec_io][l:68]mv_spec node status disable
In: uart0@20130000
Out: uart0@20130000
Err: uart0@20130000
Net: Net Initialization Skipped
No ethernet found.
Hit CTRL+C to stop autoboot: 0
SF: Detected P25Q32SH with page size 256 Bytes, erase size 4 KiB, total 4 MiB
device 0 offset 0x43000, size 0xe0000
SF: 917504 bytes @ 0x43000 Read: OK
SF: Detected P25Q32SH with page size 256 Bytes, erase size 4 KiB, total 4 MiB
device 0 offset 0x39000, size 0x497b
SF: 18811 bytes @ 0x39000 Read: OK

Booting kernel from Legacy Image at 80a00000 ...

Image Name: AliOS Things#0x00000000
Image Type: ARM Linux Kernel Image (lzma compressed)
Data Size: 767662 Bytes = 749.7 KiB
Load Address: 80000000
Entry Point: 80000000
Verifying Checksum ... OK

Flattened Device Tree blob at 813f0000

Booting using the fdt blob at 0x813f0000
Uncompressing Kernel Image
Uncompressing ... (addr=81400000 size=f00000)
Using Device Tree in place at 813f0000, end 813f797a

Starting kernel ...

[A/DRV] cpu freq: 400 MHz
[A/DRV] hclk/dclk freq: 200 MHz
[A/DRV] dphyclk freq: 200 MHz
[A/DRV] asic freq: 400 MHz
[A/DRV] gclk freq: 100 MHz
[A/DRV] vclk freq: 200 MHz
[A/DRV] peri freq: 600 MHz
[A/AOS] [19]kernel init
[A/DRV] Board info: EVB_CBD_AK3918EV200X_V1.0.0
[A/DRV] Dts version: V0.0.01
[A/DRV] phys memory start addr: 0x80000000 size: 0x4000000
[A/DRV] phys reserved memory addr: 0x81400000 size: 0xf00000
[mvspec_gpio_init][l:221]mv_spec node status disable
[A/DRV] SPI0_CLK:25000000 Hz
[A/AOS] Device Size Offset Name
[A/AOS] mtdblock0 220KB 0x00000000 SPL
[A/AOS] mtdblock1 4KB 0x00037000 ENV
[A/AOS] mtdblock2 4KB 0x00038000 ENVBK
[A/AOS] mtdblock3 40KB 0x00039000 DTB
[A/AOS] mtdblock4 896KB 0x00043000 KERNEL
[A/AOS] mtdblock5 1984KB 0x00123000 ROOTFS
[A/AOS] mtdblock6 24KB 0x00313000 CONFIG
[A/AOS] mtdblock7 924KB 0x00319000 CONFIG2
[A/AOS] mtdblock8 4096KB 0x00000000 ALL
[A/AOS] mount type 5 dev /dev/ram0 path /tmp
[A/AOS] vfs_register_fs path /tmp, ret 0
[A/BEN] Mount ramfs on /tmp successfully.
[A/AOS] mount type 3 dev /dev/mtdblock5 path /
[A/AOS] vfs_register_fs path /, ret 0
[A/BEN] Mount romfs on / successfully.
[A/AOS] mount type 2 dev /dev/mtdblock6 path /etc/config
[A/AOS] vfs_register_fs path /etc/config, ret 0
[A/BEN] Mount littlefs on /etc/config successfully.
[A/AOS] mount type 2 dev /dev/mtdblock7 path /mnt/mtd
[A/AOS] vfs_register_fs path /mnt/mtd, ret 0

[A/BEN] Mount littlefs on /mnt/mtd successfully.
[A/AOS] aos 3.4.3 build@Aug 4 2025 16:47:09 by root@PC-202404251642
[A/AOS] kernel heap: 1024 KB, Used: 223 KB, Free: 800 KB
[A/DRV] i2c0 frequency request 400000KHz set to 390 KHz
[A/DRV] adapter [i2c0] registered
[A/DRV] anyka,dma-reserve register ok
[A/DRV] number of video dev: 1
[A/DRV] input_video_init 3173
[A/DRV] of_video_dev_reg vi0 register ok
[A/DRV] i2c_add_driver i2c_client attach driver [sc1346] done!!!
[F/DRV] MIPI: camera_sp230a_reg i2c add driver failed, ret:-1!
LWIP2.1.3_V1.2.1
[A/AOS] netdev_register netdev 0x803682b8 name usb0
[A/DRV] anyka,ak39ev200-efuse register ok
[A/AOS] netdev_register netdev 0x8036c778 name eth0
[A/ETH] anyka,ak39ev200-ethernet register ok
[A/MCI] mmc0: detect gpio = 34
[E/DRV] of_get_named_gpiod_flags: can't parse 'reset-pins' property of node '/soc/mmc0@20100000[0]'
[A/MCI] mmc0: power_save: 1 detect mode: 2 (1 - clk, 2 - gpio, 3 - data3)
[A/MCI] mmc0: gpio_power: 57 active level: 0
[A/MCI] mmc0: min fre: 400000Hz max fre: 25000000Hz
[A/MCI] mmc0: card status = 1 (0 - OFF, 1 - IN)
[A/MCI] mmc1: gpio_rst: 62 active level: 0
[A/MCI] mmc1: power_save: 1 detect mode: 0 (1 - clk, 2 - gpio, 3 - data3)
[A/MCI] mmc1: gpio_power: 51 active level: 0
[A/MCI] mmc1: min fre: 400000Hz max fre: 25000000Hz
[A/MCI] mmc1: card status = 1 (0 - OFF, 1 - IN)
[A/MOT] motor0 device register
[A/MOT] motor1 device register
[A/MOT] ms32006 ircut register ok
[A/DRV] i2c_add_driver i2c_client attach driver [ms32006] done!!!
[A/AOS] [92]application start
[A/MCI] mmc0: detect thread start
[A/MCI] mmc1: detect start
[A/BEN] CISTPL_MANFID 0x007a, 0x6011
[A/MCI] mmc1: clock: 25000000Hz

_async_pool_ble_nc mutex init success
_async_pool_connections mutex init success
readdir mutex init success
init 1=======
factorytools mutex init success
_async_pool_osd mutex init success
mvt utilities ver:1.14.7_b9f5502[build:Mar 8 2025_15:13:37]
ANYKA:welcome user space, timestamp:1969
------------------------ mvs into ----------------------
[1970-01-01 07:00:02] [0:00:01:955] [DEF] version:V1.1.0 build date:Aug 4 2025 17:18:33
====== log maintainer params ======
max cache size: 71680
syslog mode: 1
log cfg root local: /mnt/mtd/mvconf/
log cfg root extern: /mnt/sdcard/
iotc cert file: /mnt/mtd/mvconf/certs/mviot.crt

log maintainer syslog to init
[A/BEN] load /usr/user.strip.elf success
[1970-01-01 07:00:02] [0:00:02:080] [DEF] [WDG] _pth_watchdog_worker watchdog start...
** ak common version: libplat_common V1.0.23 mem_trace_flag:0 **
[E/LFS] components/fs/littlefs/littlefs_vfs.c:657:error: lfs_vfs_open /mnt/mtd/mvconf/mv_gattr1.db failed, ret - -2
[MVT-SDB][WAR]###### [0] of all reload db vm [1] (code:-15)
[1970-01-01 07:00:02] [0:00:02:100] [DEF] mv_ipc_config_load start
[ VI][1970-01-01 00:00:02 190] [ak_vi_open:400] register device, device id:[0]
[ VI][1970-01-01 00:00:02 190] new device
[ VI][1970-01-01 00:00:02 190] [vi_register_device:279] new dev=0x10398748
ispsdk_lib version:libplat_isp_sdk V7.0.01
open isp dev: /dev/isp-param-0
[E/DRV] ispdrv_init 3476
[E/DRV] dma alloc vir:0x0xc0010320, phy:0x80438320
[A/DRV] isplib: isp_module_init: ak_isp_drv_lib V0.3.05
[A/DRV] isplib: isp2 module init: isp_struct size=43432, dma_area=0x0xc0010320, dma_bytes=11808, io_base=0xf0300000
[A/DRV] isplib: isp2_module_init cb:0x803a338c, sensor_cb:0x80363968, reg_base:0xf0300000, isp_struct:0x803741c8
[A/DRV] isplib: all:2151908128-0
[A/DRV] isplib: stat:2151915648-0
[A/DRV] isplib: 3d:0
--- AK_ISP_sdk_init g_isp_fd[0]=515 ---
[ VI][1970-01-01 00:00:02 200] [vi_dev_open:235] vi device open DEV0!
[ VI][1970-01-01 00:00:02 200] [vi_dev_open:248] open sensor dev: /dev/v4l-subdev0
[ VI][1970-01-01 00:00:02 205] [vi_dev_open:258] --- vi_dev_open g_sensor_fd[0]=517 ---
[A/DRV] ak_cam_file_open 964 input_id:0, chn_id:0
[A/DRV] ak_cam_file_open 964 input_id:0, chn_id:1
[ VI][1970-01-01 00:00:02 205] register vi device ok, dev_count=1
=== manufacturers_num[0], sensor_id_num[0], type[1345], width[1280], height[720], manufacturers[sc] ===
=== manufacturers_num[0], sensor_id_num[1], type[1346], width[1280], height[720], manufacturers[sc] ===
=== width[1280], height[720], manufacturers[sc] ===
[1970-01-01 07:00:02] [0:00:02:210] [DEF] sensor width:1280 high:720
[1970-01-01 07:00:02] [0:00:02:210] [DEF] read /mnt/mtd/mvconf/avframe_attr.ini
[1970-01-01 07:00:02] [0:00:02:225] [DEF] read /mnt/mtd/mvconf/record.ini
[1970-01-01 07:00:02] [0:00:02:235] [DEF] read /mnt/mtd/mvconf/variable_args.ini
[1970-01-01 07:00:02] [0:00:02:260] [DEF] read /mnt/mtd/mvconf/factory_const.ini
[1970-01-01 07:00:02] [0:00:02:280] [DEF] new force level:0 old force level:0 sensor w:1280 h:720 target w:1280 h:720
============= dev attr ============
lens type: 0
network reset mode: 1
vframe encode type: 1
aframe encode type: 5
light ctrl: 3
force resolution lv: 0
main fps: 20, sub fps: 20
fps-max: d[0]-n[0]
Main: 1280 * 720
Sub: 640 * 360

[1970-01-01 07:00:02] [0:00:02:285] [DEF] read /mnt/mtd/mvconf/version.ini
[1970-01-01 07:00:02] [0:00:02:295] [DEF] read /mnt/mtd/authority.ini
[1970-01-01 07:00:02] [0:00:02:365] [DEF] ptz h speed:0 step:80
[1970-01-01 07:00:02] [0:00:02:365] [DEF] ptz v speed:0 step:50
[1970-01-01 07:00:02] [0:00:02:365] [DEF] ptz vague_full_ag_H:3400 vague_full_ag_V:1200
[A/MCI] [sd connect]
[A/AOS] SD card capacity 15267840 KB.
[A/MCI] mmc0: clock: 25000000Hz
[1970-01-01 07:00:02] [0:00:02:660] [DEF] ====== AUTHORITY_SUPPORT ======
[1970-01-01 07:00:02] [0:00:02:665] [DEF] PTZ: pos-mark-max <6>
efuse read globe ID length: 6
globe id:
03 E9 00 02 08 3E
u64 global id: 03e90002083e
[1970-01-01 07:00:02] [0:00:02:770] [DEF] pcba_check_enable:0, don't need check pcba
[1970/01/01 08:00:02][0:00:02.770][INF][sdcard]mv_sdcard_manage_init start

[1970-01-01 07:00:02] [0:00:02:780] [DEF] *** to -> mount -t akfat /dev/mmcblk0p0 /mnt/sdcard ***
[A/AOS] vfs_register_fs path /mnt/sdcard, ret 0
[A/DRV] mount time: 757ms
[A/BEN] Mount fatfs on /mnt/sdcard successfully.
[2025/01/06 13:45:41][0:00:03.550][INF][sdcard]_pth_listen_sdcard[407] sdcard is FAT32 format _u32_cluster_size:0 _s32_retval:-27
[2025/01/06 13:45:41][0:00:03.550][INF][sdcard][_pth_listen_sdcard][start][sdcard status:8]
mvs_factory_config_load _s32_factory_config_ret:-4
[ VQE][2025-01-06 05:45:41 130] [ak_vqe_inner_open:2547] ak_vqe_inner_open entry...ai_vqe = 0x0, ao_vqe = 0x10398890
[ ECHO][2025-01-06 05:45:41 135] ## --AudioFilter Version V1.16.03, Echo--
[ ECHO][2025-01-06 05:45:41 140] ## jitterBuf: 0x10398af0
[ ECHO][2025-01-06 05:45:41 140] ## _SD_Echo_Open far_path (0x10398a78)
[ ECHO][2025-01-06 05:45:41 165] ## Echo: load far_NR (disable)
[ ECHO][2025-01-06 05:45:41 170] ## Echo: load far_Volume
[ ECHO][2025-01-06 05:45:41 170] ## ASLC OPEN OK ena:1, lookAheadLen:96
[ VQE][2025-01-06 05:45:41 205] [ak_vqe_inner_open:2645] ak_vqe_inner_open exit...
[ ECHO][2025-01-06 05:45:41 235] ## Echo: set far_Volume param
[ ECHO][2025-01-06 05:45:41 250] ## Echo: set far_NR param (enable)
mv_ao_init success...
mv_adec_open success
[ ECHO][2025-01-06 05:45:41 335] ## Echo: set far_Volume param
[2025-01-06 12:45:41] [0:00:03:910] [DEF] update patch check start
play mp3 file /mnt/mtd/mvsound/sf_devstarting.mp3...
check no patch
mvs core ver:2.0.14_9f55626[build:Mar 8 2025_15:13:34]
[MVT-SDB][WAR]db idx[2] select size failed (0)
[MVT-SDB][WAR]db idx[3] select size failed (0)
[MVT-SDB][WAR]db idx[3] select size failed (0)
[E/LFS] components/fs/littlefs/littlefs_vfs.c:657:error: lfs_vfs_open /mnt/mtd/mvconf//mvs_bs_cst.db failed, ret - -2
[MVT-SDB][WAR]###### [3] of all reload db vm [769] (code:-15)
[2025-01-06 12:45:41] [0:00:04:320] [DEF] mv_network_init start
[2025-01-06 12:45:41] [0:00:04:355] [DEF] [NETWORK] dns_group:0
_iotc_attr_of_config_spec[l:235]Get network if abl...
[A/PHY] Connected Generic PHY id 0x937c4024
[2025-01-06 12:45:41] [0:00:04:475] [DEF] [ETHER] eth0 set 0
[2025-01-06 12:45:41] [0:00:04:475] [DEF] [NETWORK] flag set:0
libdrv_wifi_atbm603x V1.4.9_beta

tbmwifi fw type:only wifi
[atbm_log]:atbm_init_firmware
[atbm_log]:[Wifi] Enter atbm_sdio_module_init
[atbm_log]:SVN_VER=2666,DPLL_CLOCK=24,BUILD_TIME=[===SDIO-ATHENAB==
[atbm_log]:atbm_sdio_register_init
[atbm_log]:atbm: Atbmwifi_halEntry() <===
[atbm_log]:atbm_register_bh++++
[atbm_log]:atbm_register_bh---
chipver: ASMLITE
[atbm_log]:atbm_before_load_firmware++
[atbm_log]:atbm_start_load_firmware++
[atbm_log]:atbm_start_load_firmware: START DOWNLOAD ICCM=========
[atbm_log]:atbm_load_firmware_generic: addr 10000: len 15000
[atbm_log]:atbm_start_load_firmware: START DOWNLOAD DCCM=========
[atbm_log]:atbm_load_firmware_generic: addr 800000: len 9000
[atbm_log]:atbm_start_load_firmware: FIRMWARE DOWNLOAD SUCCESS
[atbm_log]:atbm_after_load_firmware++
[atbm_log]:firmwareCap f1ad
[atbm_log]:firmwareCap2 11a4
[atbm_log]:wsm_startup_indication : resv[0]
[atbm_log]:wsm_caps.firmwareCap 11a4f1ad
[atbm_log]:apollo wifi WSM init done.
Input buffers: 29 x 1648 bytes
Hardware: 7.0
WSM firmware [=MODEM==SDIO=-NoBle-Jul 15 2024 14:20:58]
[atbm_log]:LmacVersion: 20685, build: 4229, api: 1060, cap: 0x11A4F1AD Config[8030408] expection 9006fdc, ep0 cmd addr 0
[atbm_log]:CAPABILITIES_ATBM_PRIVATE_IE [0]
[atbm_log]:CAPABILITIES_IPC [1]
[atbm_log]:CAPABILITIES_NO_CONFIRM [1]
[atbm_log]:CAPABILITIES_SDIO_PATCH [0]
[atbm_log]:CAPABILITIES_NO_BACKOFF [1]
[atbm_log]:CAPABILITIES_CFO [0]
[atbm_log]:CAPABILITIES_AGC [1]
[atbm_log]:CAPABILITIES_TXCAL [1]
[atbm_log]:CAPABILITIES_MONITOR [0]
[atbm_log]:CAPABILITIES_CUSTOM [0]
[atbm_log]:CAPABILITIES_SMARTCONFIG [0]
[atbm_log]:CAPABILITIES_ETF [1]
[atbm_log]:CAPABILITIES_LMAC_RATECTL [1]
[atbm_log]:CAPABILITIES_LMAC_TPC [1]
[atbm_log]:CAPABILITIES_LMAC_TEMPC [1]
[atbm_log]:CAPABILITIES_CTS_BUG [0]
[atbm_log]:CAPABILITIES_USB_RECOVERY_BUG [0]
[atbm_log]:CAPABILITIES_USE_IPC [0]
[atbm_log]:CAPABILITIES_OUTER_PA [0]
[atbm_log]:CAPABILITIES_POWER_CONSUMPTION [1]
[atbm_log]:CAPABILITIES_RSSI_DECIDE_TXPOWER [0]
[atbm_log]:CAPABILITIES_RTS_LONG_DURATION [1]
[atbm_log]:CAPABILITIES_TX_CFO_PPM_CORRECTION[1]
[atbm_log]:CAPABILITIES_SHARE_CRYSTAL [0]
[atbm_log]:CAPABILITIES_HW_CHECKSUM [0]
[atbm_log]:CAPABILITIES_SINGLE_CHANNEL_MULRX [0]
[atbm_log]:CAPABILITIES_CFO_DCXO_CORRECTION [1]
[atbm_log]:EX_CAPABILITIES_TWO_CHIP_ONE_SOC [0]
[atbm_log]:EX_CAPABILITIES_MANUAL_SET_AC [0]
[atbm_log]:EX_CAPABILITIES_LMAC_BW_CONTROL [1]
[atbm_log]:EX_CAPABILITIES_SUPPORT_TWO_ANTENNA [0]
[atbm_log]:EX_CAPABILITIES_ENABLE_STA_REMAIN_ON_CHANNEL [1]
[atbm_log]:EX_CAPABILITIES_ENABLE_PS [1]
[atbm_log]:EX_CAPABILITIES_TX_REQUEST_FIFO_LINK [0]
[atbm_log]:EX_CAPABILITIES_DRIVER_PHY_REG_INIT [0]
[atbm_log]:EX_CAPABILITIES_DRIVER_PROCESS_BA [1]
[atbm_log]:EX_CAPABILITIES_WAKEUP_HOST_TX [0]
driver_setup_ba:1
[atbm_log]:lmc_wakeup_host:0
[atbm_log]:not need phy init in driver
[atbm_log]:atbmwifi_queue_init,cap(64)
[atbm_log]:atbmwifi_queue_init,cap(64)
[atbm_log]:atbmwifi_queue_init,cap(64)
[atbm_log]:atbmwifi_queue_init,cap(64)
[atbm_log]:efuse data is [0x1,0x3b,0x1f,0x1f,0x1e,0x10,0x0,0x0,0x2c:0xd8:0xde:0x87:0xa6:0xf9]
[atbm_log]:read /etc/config/atbm_wifi_macaddr.txt error
[atbm_log]:MAC Addr[0]:[2c:d8:de:87:a6:f9]
[atbm_log]:read /etc/config/atbm_txpwer_dcxo_cfg.txt error
[atbm_log]:atbmwifi_netstack_init
[atbm_log]:__wpa_event_init
[atbm_log]:atbmwifi_netstack_init END
[atbm_log]:atbm_alloc_netdev,netdev(0x803d4bc0),nif(0x8038d080),priv(0x803d4bd4)
[atbm_log]:atbm_alloc_netdev,netdev(0x803da630),nif(0x8038d1b8),priv(0x803da644)
_iotc_attr_of_config_spec[l:235]Get network if abl...
[atbm_log]:auto_cfo:cfo 1 0 ,buf_len:8
[atbm6031_init]-line:113 wifi init done!
wifi init time is:208ms
[A/WLA] wlan init success
[2025-01-06 12:45:42] [0:00:04:685] [DEF] [NETWORK] module type:110 mode:2

[mv_server_netstate_change][ret:-10]
[atbm_log]:atbmwifi_start_wifimode:other_alive_if(0),all_alive_if(0)
atbm6031_set_mode 1
[A/AOS] netdev_register netdev 0x803e6c18 name wlan0
[atbm_log]:Event:(9),if_type:(0)
[A/WLA] wlan indicate event: 3
[A/WLA] wlan indicate event: 6
[atbm_log]:atbmwifi_del_key err (0 1)
[atbm_log]:atbmwifi_del_key err (0 0)
[atbm_log]:wpa_supplicant_event_disassoc 521
[atbm_log]:wpa_s->wpa_state =0
[atbm_log]:wpa_deauthen
[atbm_log]:Event:(5),if_type:(0)
[atbm_log]:atbm_reorder_func_reset.
[atbm_log]:Event:(0),if_type:(0)
event ID = 106, 5
event ID = 106, 9
[atbm_log]:All Interface is down
atbm6031_set_mode 0
[F/DRV] 18:25:02 wlan_net_dev_unregister 342
[A/AOS] vfs_inode_release node /dev/wlan0 will be removed!
[2025-01-06 12:45:42] [0:00:04:800] [DEF] pwifi_info->net_info.av8_mac_str:2c:d8:de:87:a6:f9
_iotc_attr_of_config_spec[l:235]Get network if abl...
[mv_server_prepare][model_id: A2X1EXHR][ver:2010600]
[bind check][mac:(2c:d8:de:87:a6:f9)]
mvspv2 pm ver:1.0.9_3e8d6e8[build:Mar 8 2025_15:13:32]
[2025/01/06 13:45:43][0:00:06.375][INF][mvscomm]model:[A2X1EXHR] dver:[2010600] did: [122083952], pid: [32], ctype: [2], internal ts basic >ms: [1736142337460]
[2025-01-06 12:45:43] [0:00:06:420] [DEF] [mv_server_prepare]exit
[2025-01-06 12:45:43] [0:00:06:420] [DEF] media init start
== mv_platform_ai_init ==
frame_len=1920
mv_ai_init success...
mv_aenc_param->audio_codec_type =============== 1
[ SD_AENC][2025-01-06 05:45:43 945] ## -- AudioCodec Version V1.22.00, type: 17, g711 enc --
[ SD_AENC][2025-01-06 05:45:43 945] ## _SD_Encode_Open OK (0x10405c78)
mv_aenc_open success
[ VQE][2025-01-06 05:45:44 240] [ak_vqe_inner_open:2547] ak_vqe_inner_open entry...ai_vqe = 0x10405a1c, ao_vqe = 0x0
[ ECHO][2025-01-06 05:45:44 250] ## --AudioFilter Version V1.16.03, Echo--
[ ECHO][2025-01-06 05:45:44 250] ## jitterBuf: 0x1040b458
[ ECHO][2025-01-06 05:45:44 250] ## _SD_Echo_Open near_path (0x1040b360)
[ ECHO][2025-01-06 05:45:44 290] ## Echo: load NR (enable)
[ ECHO][2025-01-06 05:45:44 295] ## Echo: set AGC param (enable)
[ ECHO][2025-01-06 05:45:44 295] ## Echo: load near_EQ
[ ECHO][2025-01-06 05:45:44 295] ## Echo: load near_Volume
[ ECHO][2025-01-06 05:45:44 295] ## ASLC OPEN OK ena:1, lookAheadLen:96
[ ECHO][2025-01-06 05:45:44 370] ## Echo: load AEC (disable)
[ VQE][2025-01-06 05:45:44 375] [loopback_start:1643] aec_enable =0, user->ai_open=1
[ VQE][2025-01-06 05:45:44 410] [ak_vqe_inner_open:2645] ak_vqe_inner_open exit...
[ VQE][2025-01-06 05:45:44 410] [ak_vqe_inner_set_ai_jitterbuf_upperBound:3951] osal_vqe_get_dac entry...
[ ECHO][2025-01-06 05:45:44 410] ## Echo: set near_JitterBuf param
[ VQE][2025-01-06 05:45:44 410] [ak_vqe_inner_set_ai_jitterbuf_upperBound:3972] exit...
== mv_platform_ai_start_capture ==
*** ai capture start, _g_ai_handle_id ***
wait aenc param copy over
=== mvak_start_ai_encode success handle_id ===
[ ECHO][2025-01-06 05:45:44 640] ## Echo: set near_Volume param
Play Finished, mp3 decoder size:118656
to set mvp_ai_volume_set : 80
=== manufacturers_num[0], sensor_id_num[0], type[1345], width[1280], height[720], manufacturers[sc] ===
=== manufacturers_num[0], sensor_id_num[1], type[1346], width[1280], height[720], manufacturers[sc] ===
=== width[1280], height[720], manufacturers[sc] ===
[2025-01-06 12:45:44] [0:00:07:205] [DEF] sensor info sensor_type[1346], sensor_width[1280], sensor_height[720], sensor_manufacturers[sc]
[2025-01-06 12:45:44] [0:00:07:240] [DEF] get config "isp_cust" = 0, "isp_patch" = 0
mvp_isp_init
[_isp_prepare][l:225]try catch full patchpath: [/usr/isp_sc1346/c0/l0p0.conf]
[_isp_prepare][l:235]full patchpath: [/usr/isp_sc1346/c0/l0p0.conf] not exist!!!
[_isp_prepare][l:253]try to read patch [/usr/isp_sc1346/c0/l0p0.conf.p] result: 0
isp path [/tmp/isp_sc1346_c0l0p0.conf]
[ VPSS][2025-01-06 05:45:44 760] [isp_open:91] dev:0 already opened!
[E/LFS] components/fs/littlefs/littlefs_vfs.c:657:error: lfs_vfs_open /etc/config/styleId failed, ret - -2
[ VPSS][2025-01-06 05:45:44 765] [isp.conf]version: DVP_V3_041101, sensor id: 0x1346, style id: 0
[ VPSS][2025-01-06 05:45:44 765] isp subfile 0, modify time: 2025-7-4 17:07:38
[ VPSS][2025-01-06 05:45:44 765] 1.first init isp_sc1346.conf file.
23060701 change exp 20fps
23110801 change exp
24041101 change exp bc_rate min▒▒▒▒▒▒AE▒▒▒

[ VPSS][2025-01-06 05:45:44 765] isp subfile 1, modify time: 2024-12-4 18:02:31
[ VPSS][2025-01-06 05:45:44 765] 1.first init isp_sc1346.conf file.

[ VPSS][2025-01-06 05:45:44 765] [check_file:419] check isp cfg: /tmp/isp_sc1346_c0l0p0.conf OK
[ VPSS][2025-01-06 05:45:44 765] [isp_module_init:1540] chipid:0x20150200 !
[ VPSS][2025-01-06 05:45:44 775] [check_fps_para:465] hight light:
frame_rate=20 max_exp_time=1125 low_light_gain=24
[ VPSS][2025-01-06 05:45:44 775] [check_fps_para:470] low light:
frame_rate=15 max_exp_time=1494 light_gain=8
[ VPSS][2025-01-06 05:45:44 775] [init_fps_info:601] hight light fps: 20
[ VPSS][2025-01-06 05:45:44 775] [isp_set_sensor_fps:2653] set sensor fps: 20
[ VPSS][2025-01-06 05:45:44 775] [set_fps:237] set dev:0 fps:20 ok
[E/DRV] MIPI: ak_sensor_store_initial_regs para.num;140
load [/tmp/isp_sc1346_c0l0p0.conf] result = 0

Get vi info res main[1280, 720], sub[640, 360]

[A/DRV] ak_cam_vidioc_cropcap 1495 input_id:0, chn_id:0

set devid [0] ------>
crop.left [0](padding[0], max[0]), crop.top [0], crop.width [1280], crop.height [720]
max_width [1280], max_height [720], sub_max_width [640], sub_max_height [360]

[A/DRV] ak_cam_vidioc_querycap 1242 input_id:0, chn_id:0
[A/DRV] ak_cam_vidioc_cropcap 1495 input_id:0, chn_id:0
[A/DRV] ak_cam_vidioc_set_crop 1561 input_id:0, chn_id:0
[A/DRV] ak_cam_vidioc_set_crop chn_id:0 left:0, top:0, c.left:0, c.top:0
[A/DRV] isplib: isp_vi_set_crop sx:0,sy:0,w:1280,h:720

get devid [0] ------>
crop.left [0], crop.top [0], crop.width [1280], crop.height [720]
max_width [1280], max_height [720], sub_max_width [640], sub_max_height [360]

[A/DRV] ak_cam_vidioc_set_format 1400, input_id:0, chn_id:0,pix->width:1280, pix->height:720
[A/DRV] isplib: isp_vo_set_main_channel_scale enter.(1280,720,0,1280,720)
[A/DRV] ak_cam_vidioc_set_format 1400, input_id:0, chn_id:1,pix->width:640, pix->height:360
[A/DRV] ak_cam_vidioc_reqbufs 1796 input_id:0, chn_id:0
[A/DRV] ak_vb2_queue_setup input_id:0, chn_id:0 *count:2, sizeimage:1382400
[A/DRV] ak_cam_vidioc_querybuf 1821 input_id:0, chn_id:0
[A/DRV] ak_cam_vidioc_querybuf 1821 input_id:0, chn_id:0
[A/DRV] ak_vb2_buf_init 480 input_id:0, chn_id:0
[A/DRV] ak_vb2_buf_init 480 input_id:0, chn_id:0
[F/DRV] set_interface dvp
[A/DRV] set_pinctrl_vi 151
[A/DRV] set_pclk_polar input_id:0
[F/DRV] set_pclk_polar pclk edge is rising
[A/DRV] set_sclk 288
[A/DRV] set_sclk get rate:24000000 end
[A/DRV] set_ae_fast_default
[E/DRV] MIPI: calc_vts_tmp 2250000
[A/DRV] get_input_scan_method get scan method NONE, set PROGRESSIVE.
[A/DRV] ak_cam_vidioc_streamon 1898 input_id:0, chn_id:0
[A/DRV] ak_vb2_start_streaming 738 input_id:0, chn_id:0 count:2
[A/DRV] ak_vb2_start_streaming 757 input_id:0, chn_id:0 done:0
[A/DRV] first_chn_input_isp_init 646 enter
[A/DRV] isplib: isp_vi_start_capturing 1672 isp_id:0
[A/DRV] ak_vb2_start_streaming 827 input_id:0, chn_id:0 state: 6
[A/DRV] ak_cam_vidioc_reqbufs 1796 input_id:0, chn_id:1
[A/DRV] ak_vb2_queue_setup input_id:0, chn_id:1 *count:2, sizeimage:345600
[A/DRV] ak_cam_vidioc_querybuf 1821 input_id:0, chn_id:1
[A/DRV] ak_cam_vidioc_querybuf 1821 input_id:0, chn_id:1
[A/DRV] ak_vb2_buf_init 480 input_id:0, chn_id:1
[A/DRV] ak_vb2_buf_init 480 input_id:0, chn_id:1
[A/DRV] ak_cam_vidioc_streamon 1898 input_id:0, chn_id:1
[A/DRV] ak_vb2_start_streaming 738 input_id:0, chn_id:1 count:2
[A/DRV] ak_vb2_start_streaming 757 input_id:0, chn_id:1 done:1
[A/DRV] ak_vb2_start_streaming 781 input_id:0, chn_id:1
[A/DRV] ak_vb2_start_streaming 827 input_id:0, chn_id:1 state: 3
set standard mode failed [-4]
[E/DRV] uio0 has opened! open_count=2
[AKV_VENC][2025-01-06 05:45:44 915]
--VIDAK39--Enc AK39 Encoder Lib V1.10.08--

is_drop_frame 2683 drop frame 0
[A/DRV] [7513] dev_0_seq = 1, ae = (256,256,256,894), lumi(avg,comp,target) = (0,0,55)
[A/DRV] dev_id =0, target_lumi = 55, cur_lumi = 0
cur_ae:(256,256,256,894), cur_lumi=0
est_ae:(8192,256,384,1125), target_lumi=55
[A/DRV] [metering] set exp_type = 0
metering_status_0 = 0
[A/DRV] set_sensor_fps_async input_id:0 set fps:20 success
is_drop_frame 2683 drop frame 2
[A/DRV] [7548] dev_0_seq = 2, ae = (256,256,256,894), lumi(avg,comp,target) = (0,0,55)
is_drop_frame 2683 drop frame 1
[A/DRV] [7583] dev_0_seq = 3, ae = (8192,256,384,1125), lumi(avg,comp,target) = (0,0,55)
[AKV_VENC][2025-01-06 05:45:45 045]
--VIDAK39--Enc AK39 Encoder Lib V1.10.08--

is_drop_frame 2683 drop frame 0
[A/DRV] [7633] dev_0_seq = 4, ae = (8192,256,384,1125), lumi(avg,comp,target) = (2,2,55)
[A/DRV] dev_id =0, target_lumi = 55, cur_lumi = 2
cur_ae:(8192,256,384,1125), cur_lumi=2
est_ae:(8192,256,384,1125), target_lumi=55
[A/DRV] [metering] set exp_type = 0
metering_status_0 = 0
is_drop_frame 2683 drop frame 2
[A/DRV] [7678] dev_0_seq = 5, ae = (8192,256,384,1125), lumi(avg,comp,target) = (3,3,55)
is_drop_frame 2683 drop frame 1
[A/DRV] [7728] dev_0_seq = 6, ae = (8192,256,384,1125), lumi(avg,comp,target) = (3,3,55)
[AKV_VENC][2025-01-06 05:45:45 205]
--VIDAK39--Enc AK39 Encoder Lib V1.10.08--

is_drop_frame 2683 drop frame 0
[AKV_VENC][2025-01-06 05:45:45 205] ### 152 ###
[AKV_VENC][2025-01-06 05:45:45 210] ### 183 ###
[A/DRV] [7778] dev_0_seq = 7, ae = (8192,256,384,1125), lumi(avg,comp,target) = (3,3,55)
[A/DRV] dev_id =0, target_lumi = 55, cur_lumi = 3
cur_ae:(8192,256,384,1125), cur_lumi=3
est_ae:(8192,256,384,1125), target_lumi=55
[A/DRV] [metering] set exp_type = 0
metering_status_0 = 0
is_drop_frame 2683 drop frame 2
[A/DRV] [7828] dev_0_seq = 8, ae = (8192,256,384,1125), lumi(avg,comp,target) = (3,3,55)
is_drop_frame 2683 drop frame 1
[A/DRV] [7878] dev_0_seq = 9, ae = (8192,256,384,1125), lumi(avg,comp,target) = (3,3,55)
is_drop_frame 2683 drop frame 0
[A/DRV] [7928] dev_0_seq = 10, ae = (8192,256,384,1125), lumi(avg,comp,target) = (3,3,55)
[A/DRV] dev_id =0, target_lumi = 55, cur_lumi = 3
cur_ae:(8192,256,384,1125), cur_lumi=3
est_ae:(8192,256,384,1125), target_lumi=55
[A/DRV] [metering] set exp_type = 0
metering_status_0 = 4
is_drop_frame 2683 drop frame 1
[A/DRV] [7978] dev_0_seq = 11, ae = (8192,256,384,1125), lumi(avg,comp,target) = (3,3,55)
is_drop_frame 2683 drop frame 0
go out play mp3 file /mnt/mtd/mvsound/sf_devstarting.mp3 , break_status:0
[A/DRV] [8028] dev_0_seq = 12, ae = (8192,256,384,1125), lumi(avg,comp,target) = (3,3,55)
[ OSD][2025-01-06 05:45:45 510] [request_osd_mem:480] size:460800
[ OSD][2025-01-06 05:45:45 510] [request_osd_mem:498] INFO:video_ch0, osd_rect:0, p_osd_buffer:0xa6d2a0, p_osd_phy:0x81d6d2a0 >size: 460800, width:1280, height:720
[ OSD][2025-01-06 05:45:45 510] [request_osd_dma_mem:379] size:921600
[ OSD][2025-01-06 05:45:45 515] [request_osd_dma_mem:443] INFO:video_ch0, osd_rect:0, dma_vaddr: 0xaddaa0, phyaddr: 0x81dddaa0 >size: 921600 w: 1280 h: 720
[A/DRV] [8078] dev_0_seq = 13, ae = (8192,256,384,1125), lumi(avg,comp,target) = (3,3,55)
[A/DRV] [8078] ***** drv get_first_frame ******, dev_0_seq = 13
[A/DRV] [metering] set exp_type = 1
metering_status_0 = 5
[ OSD][2025-01-06 05:45:45 610] [request_osd_mem:480] size:115200
[ OSD][2025-01-06 05:45:45 610] [request_osd_mem:498] INFO:video_ch1, osd_rect:0, p_osd_buffer:0xbbeaa0, p_osd_phy:0x81ebeaa0 >size: 115200, width:640, height:360
[ OSD][2025-01-06 05:45:45 610] [request_osd_dma_mem:379] size:230400
[ OSD][2025-01-06 05:45:45 610] [request_osd_dma_mem:443] INFO:video_ch1, osd_rect:0, dma_vaddr: 0xbdaca0, phyaddr: >0x81edaca0 >size: 230400 w: 640 h: 360
[_pth_osd_worker][l:455]to run ...
=== mvp_isp_flip_and_mirror flip_mirror:3 sensor type [4934] ===
[2025-01-06 12:45:45] [0:00:08:275] [DEF] media init finish
[2025-01-06 12:45:45] [0:00:08:275] [DEF] mv_input_scaner_init start
[2025-01-06 12:45:45] [0:00:08:280] [DEF] ptz ctrl init
[2025-01-06 12:45:45] [0:00:08:370] [DEF] ptz speed hz:900
[2025-01-06 12:45:45] [0:00:08:370] [DEF] ptz speed hz:900
== irfm_lock_state [0] invalid of (1/3/4), set default [0:IR_FEED_STATE_AUTO] ==
[A/DRV] MAINCHN0 iomap 0x112f2a0 0x81d6d2a0 size:460800
[A/DRV] SUBCHN0 iomap 0x11a0aa0 0x81ebeaa0 size:115200
[2025-01-06 12:45:45] [0:00:08:480] [DEF] [PTZ] ===== set motor params ====
[2025-01-06 12:45:45] [0:00:08:480] [DEF] [PTZ] H steps_one_circle[3400], total_steps[3400]
[2025-01-06 12:45:45] [0:00:08:480] [DEF] [PTZ] V steps_one_circle[1200], total_steps[1200]
[2025-01-06 12:45:45] [0:00:08:480] [DEF] [PTZ] go to ptz self check
[A/MOT] [ms32006_motor_move_thread][l:453][idx:1][cur:-100]to set run step 2040
[2025-01-06 12:45:45] [0:00:08:515] [DEF] f:mvp_ircut_init l:38 /dev/ircut open fd:528
[2025-01-06 12:45:46] [0:00:08:605] [DEF] ircut IRCUT_A1_B0
[2025-01-06 12:45:46] [0:00:08:740] [DEF] ircut IRCUT_A0_B0
[ VPSS][2025-01-06 05:45:46 400] [isp_switch:266] switching isp mode -> day
[E/LFS] components/fs/littlefs/littlefs_vfs.c:657:error: lfs_vfs_open /etc/config/styleId failed, ret - -2
[ VPSS][2025-01-06 05:45:46 405] [isp.conf]version: DVP_V3_041101, sensor id: 0x1346, style id: 0
[ VPSS][2025-01-06 05:45:46 405] isp subfile 0, modify time: 2025-7-4 17:07:38
[ VPSS][2025-01-06 05:45:46 405] 1.first init isp_sc1346.conf file.
23060701 change exp 20fps
23110801 change exp
24041101 change exp bc_rate min▒▒▒▒▒▒AE▒▒▒

[ VPSS][2025-01-06 05:45:46 405] isp subfile 1, modify time: 2024-12-4 18:02:31
[ VPSS][2025-01-06 05:45:46 405] 1.first init isp_sc1346.conf file.

[ VPSS][2025-01-06 05:45:46 405] [check_file:419] check isp cfg: /tmp/isp_sc1346_c0l0p0.conf OK
[ VPSS][2025-01-06 05:45:46 420] [check_fps_para:465] hight light:
frame_rate=20 max_exp_time=1125 low_light_gain=24
[ VPSS][2025-01-06 05:45:46 425] [check_fps_para:470] low light:
frame_rate=15 max_exp_time=1494 light_gain=8
[ VPSS][2025-01-06 05:45:46 425] [init_fps_info:601] hight light fps: 20
[ VPSS][2025-01-06 05:45:46 425] [isp_set_sensor_fps:2653] set sensor fps: 20
[ VPSS][2025-01-06 05:45:46 425] [set_fps:237] set dev:0 fps:20 ok
[ VPSS][2025-01-06 05:45:46 440] [check_fps_para:465] hight light:
frame_rate=20 max_exp_time=1125 low_light_gain=24
[ VPSS][2025-01-06 05:45:46 440] [check_fps_para:470] low light:
frame_rate=15 max_exp_time=1494 light_gain=8
[ VPSS][2025-01-06 05:45:46 440] [init_fps_info:601] hight light fps: 20
[ VPSS][2025-01-06 05:45:46 440] [isp_set_sensor_fps:2653] set sensor fps: 20
[ VPSS][2025-01-06 05:45:46 440] [set_fps:237] set dev:0 fps:20 ok
[2025-01-06 12:45:46] [0:00:09:000] [DEF] [ISP] >>> schn:0 set standard mode:1, hz:50
[ VPSS][2025-01-06 05:45:46 465] [isp_set_sensor_fps:2653] set sensor fps: 20
[ VPSS][2025-01-06 05:45:46 465] [set_fps:237] set dev:0 fps:20 ok
[A/DRV] set_sensor_fps_async input_id:0 set fps:20 success
[2025-01-06 12:45:46] [0:00:09:015] [DEF] [ISP] >>> schn:0 set standard exp time:1
[2025-01-06 12:45:46] [0:00:09:060] [WARN] find sensor: 1346 irfm param, now use it
[2025/01/06 13:45:46][0:00:09.060][WRN][scaner][_irfm_run] use SOFT_IRFEED_V1
env mode:0
[2025/01/06 13:45:46][0:00:09.090][INF][mvsconn][lan]worker run...
param is null
param is null

[bind finish]
[2025/01/06 13:45:46][0:00:09.090][INF][mvsconn][wan]worker run...
[2025-01-06 12:45:47] [0:00:10:125] [DEF] -------------------- wifi sta conn -------------------
[NET] sta NET_STA_CONNECTING
[2025/01/06 13:45:47][0:00:10.125][INF][mvsmqtt]mqtt stop: finish
[mv_server_netstate_change][ret:0]
play mp3 file /mnt/mtd/mvsound/sf_connecting.mp3...
Play Finished, mp3 decoder size:61056
[A/MOT] clean_motor_steps_fast steps after clean = 0
[A/MOT] [ms32006_motor_move_thread][l:453][idx:1][cur:1940]to set run step 1440
go out play mp3 file /mnt/mtd/mvsound/sf_connecting.mp3 , break_status:0
[2025-01-06 12:45:49] [0:00:12:485] [DEF] [NETWORK] sta connect ssid:antonkam pwd:13579qetuo
[atbm_log]:atbmwifi_start_wifimode:other_alive_if(0),all_alive_if(0)

atbm6031_set_mode 1
[A/AOS] netdev_register netdev 0x803e6c18 name wlan0
[A/WLA] wlan connect state 0 0x0
atbm603x_join...
[atbm_log]:atbm_wifi_on_vif+mode 0+
start fastlink...
[atbm_log]:wsm_join
[atbm_log]:sta_join ATBM_IEEE80211_STYPE_AUTH
[atbm_log]:set_suites: rsn
[atbm_log]:p(16),g(16),k(2)
[atbm_log]:wpa[2],key_mgmt[2],privacy[1],auth_alg[0]
[atbm_log]:atbmwifi_tx_sta_mgmtframe bssid=cc 44:16
[atbm_log]:[sta]:send STYPE_AUTH
[atbm_log]:send_auth alg(0),transaction(1),ielen(0)
[atbm_log]:Event:(2),if_type:(0)
[atbm_log]:Event:(2),if_type:(0)
[atbm_log]:atbmwifi_tx_sta_mgmtframe bssid=cc 44:16
[atbm_log]:[sta]:send ASSOC_REQ
[atbm_log]:Event:(2),if_type:(0)
[atbm_log]:atbmwifi_rx_assoc_rsp
[atbm_log]:RX AssocRsp (capab=0x431 status=0 aid=2)
[atbm_log]:Event:(3),if_type:(0)
[atbm_log]:connectap success ret=0
[atbm_log]:WPA: RX M1/4-Way Handshake from cc:b2:55:9a:44:16 (ver=2)
[atbm_log]:RSN: M1/4 key data
[atbm_log]:WPA: Tx EAPOL-Key 2/4.....
[atbm_log]:WPA: Tx EAPOL-Key 2/4
[atbm_log]:[TX] wpa_state 7.assoc_ok 1
[atbm_log]:WPA: RX M3/4-Way Handshake from cc:b2:55:9a:44:16 (ver=2)
[atbm_log]:WPA: Sending EAPOL-Key 4/4
[atbm_log]:WPA:install ptk
[atbm_log]:4 and 2 way handshake done!!!!
[atbm_log]:[TX] wpa_state 9.assoc_ok 1
[atbm_log]:Event:(8),if_type:(0)
[A/WLA] wlan indicate event: 1

event ID = 106, 3
[atbm_log]:dhcp tx ----
[atbm_log]:dhcp tx ----
[atbm_log]:AMPDU[0]:action[0],tid[0],ssn[1],buff_size[0],token[0],cc:b2:55:9a:44:16
dns[0]:192.168.1.1
dns[0]:192.168.1.1

set network interface device(wlan0) dns server #1: 8.8.8.8
[2025-01-06 12:45:50] [0:00:12:950] [DEF] [NETWORK] check connect status e_module_type:110
[2025-01-06 12:45:50] [0:00:12:950] [DEF] [NETWORK] get ip:192.168.1.177 gateway:192.168.1.1
dns[1]:8.8.8.8
[NET] sta NET_STA_CONNECT_SUCC
[2025/01/06 13:45:50][0:00:12.970][INF][mvsdds]renew info if,ip,mac,cfg[wlan0,192.168.1.177,2c:d8:de:87:a6:f9,0]

[mv_server_netstate_change][ret:0]
wait wan ready ... 20
[2025/01/06 13:45:50][0:00:12.980][WRN][mvsmqtt][http]mvt http host empty !
[2025/01/06 13:45:50][0:00:12.980][WRN][mvscomm][com_http_auth_do][l:95]com http do failed -2
[2025/01/06 13:45:50][0:00:12.980][WRN][mvsmqtt][_pull_license_with_http][l:313]exp ocr (-24) at l:310; msg:"res:-2,code:0"
[atbm_log]:AMPDU[0]:action[2],tid[0],ssn[2529],buff_size[0],token[0],cc:b2:55:9a:44:16
[atbm_log]:AMPDU[0]:action[4],tid[0],ssn[0],buff_size[64],token[0],cc:b2:55:9a:44:16
event ID = 106, 0
wait wan ready ... 19
[A/MOT] clean_motor_steps_fast steps after clean = 0
[A/MOT] [ms32006_motor_move_thread][l:453][idx:1][cur:3380]to set run step 20
[A/MOT] clean_motor_steps_fast steps after clean = 0
[A/MOT] [ms32006_motor_move_thread][l:453][idx:1][cur:3380]to set run step 1680
wait wan ready ... 18
env mode:2
[ VPSS][2025-01-06 05:45:52 580] [isp_switch:266] switching isp mode -> night
[E/LFS] components/fs/littlefs/littlefs_vfs.c:657:error: lfs_vfs_open /etc/config/styleId failed, ret - -2
[ VPSS][2025-01-06 05:45:52 585] [isp.conf]version: DVP_V3_041101, sensor id: 0x1346, style id: 0
[ VPSS][2025-01-06 05:45:52 590] isp subfile 0, modify time: 2025-7-4 17:07:38
[ VPSS][2025-01-06 05:45:52 590] 1.first init isp_sc1346.conf file.
23060701 change exp 20fps
23110801 change exp
24041101 change exp bc_rate min▒▒▒▒▒▒AE▒▒▒

[ VPSS][2025-01-06 05:45:52 590] isp subfile 1, modify time: 2024-12-4 18:02:31
[ VPSS][2025-01-06 05:45:52 590] 1.first init isp_sc1346.conf file.

[ VPSS][2025-01-06 05:45:52 590] [check_file:419] check isp cfg: /tmp/isp_sc1346_c0l0p0.conf OK
[ VPSS][2025-01-06 05:45:52 605] [check_fps_para:465] hight light:
frame_rate=15 max_exp_time=1494 low_light_gain=24
[ VPSS][2025-01-06 05:45:52 605] [check_fps_para:470] low light:
frame_rate=10 max_exp_time=2244 light_gain=8
[ VPSS][2025-01-06 05:45:52 605] [init_fps_info:601] hight light fps: 15
[ VPSS][2025-01-06 05:45:52 605] [isp_set_sensor_fps:2653] set sensor fps: 15
[A/DRV] set_sensor_fps_async input_id:0 set fps:15 success
[ VPSS][2025-01-06 05:45:52 615] [set_fps:237] set dev:0 fps:15 ok
[ VPSS][2025-01-06 05:45:52 625] [check_fps_para:465] hight light:
frame_rate=15 max_exp_time=1494 low_light_gain=24
[ VPSS][2025-01-06 05:45:52 625] [check_fps_para:470] low light:
frame_rate=10 max_exp_time=2244 light_gain=8
[ VPSS][2025-01-06 05:45:52 630] [init_fps_info:601] hight light fps: 15
[ VPSS][2025-01-06 05:45:52 630] [isp_set_sensor_fps:2653] set sensor fps: 15
[ VPSS][2025-01-06 05:45:52 635] [set_fps:237] set dev:0 fps:15 ok
[A/DRV] set_sensor_fps_async input_id:0 set fps:15 success
[2025-01-06 12:45:52] [0:00:15:390] [DEF] ircut IRCUT_A0_B1
[2025-01-06 12:45:52] [0:00:15:520] [DEF] ircut IRCUT_A0_B0
wait wan ready ... 17
[A/MOT] clean_motor_steps_fast steps after clean = 0
[A/MOT] [ms32006_motor_move_thread][l:453][idx:0][cur:-100]to set run step 1280
wait wan ready ... 16
wait wan ready ... 15
[2025/01/06 13:45:55][0:00:17.990][WRN][mvsmqtt][http]mvt http host empty !
[2025/01/06 13:45:55][0:00:17.990][WRN][mvscomm][com_http_auth_do][l:95]com http do failed -2
[2025/01/06 13:45:55][0:00:17.990][WRN][mvsmqtt][_pull_license_with_http][l:313]exp ocr (-24) at l:310; msg:"res:-2,code:0"
[A/MOT] clean_motor_steps_fast steps after clean = 0
[A/MOT] [ms32006_motor_move_thread][l:453][idx:0][cur:1180]to set run step 20
[A/MOT] clean_motor_steps_fast steps after clean = 0
[A/MOT] [ms32006_motor_move_thread][l:453][idx:0][cur:1180]to set run step 580
[2025/01/06 13:45:56][0:00:18.660][INF][mvscomm]to set time cause cur->net [1736142356 / 1771735138]
[2025/01/06 13:45:56][0:00:18.660][INF][mvscomm]evt MVSPT_EVENT_SYSTIME_UPDATED call
systime updated event standard:1771735138 device:1736142356
[2026-02-22 11:38:58] [0:00:18:660] [WARN] mv_alarm_schedule_filter_flush[627] time schedule filter not init
[2026/02/22 12:38:58][0:00:18.665][WRN][sjson]key [u] force check exist failed!
[2026/02/22 12:38:58][0:00:18.665][WRN][mvscomm][_iotc_userlist_parser][l:79]{"s":1,"p":4294967295} parse failed -15
[2026/02/22 12:38:58][0:00:18.665][WRN][sjson]key [u] force check exist failed!
[2026/02/22 12:38:58][0:00:18.665][WRN][mvscomm][_iotc_userlist_parser][l:79]{"s":2,"p":4294967295} parse failed -15
[2026/02/22 12:38:58][0:00:18.680][INF][mvscsp]Alarm push start [0]
[2026/02/22 12:38:58][0:00:18.680][INF][mvsconn][wan]ddnsclient start [0]
[2026/02/22 12:38:58][0:00:18.680][INF][mvsconn][wan]Wan keykeeper start [0]
[2026/02/22 12:38:58][0:00:18.680][INF][mvsconn][wan]mqtt start [0]
[2026/02/22 12:38:58][0:00:18.685][INF][mvscomm]evt MVSPT_EVENT_IOTC_CONNECT_TRYING call
mvspt_event_handler[351] IOTC_CONNECT_TRYING
[_wait_service_ready] server ready
[2026/02/22 12:38:58][0:00:18.775][INF][mvsudip]new main P2P Domain: ipc122.w390.net => [165.154.179.91]
[2026/02/22 12:38:58][0:00:18.775][INF][mvsudip]Get P2P Domain:ipc122.w390.net
[A/DRV] [18899] ae_stable: dev_0_seq = 211,ae = (413,256,256,1494), lumi(avg,comp,target) = (65,65,60)
metering_status_0 = 7
[2026-02-22 11:38:58] [0:00:18:895] [DEF] mv_alarm_init start
[2026/02/22 11:38:58][0:00:18.970][WRN][alarm][mv_alarm_schedule_filter_init][ALL DAY MODE]
play mp3 file /mnt/mtd/mvsound/sf_connected.mp3...
[A/MOT] clean_motor_steps_fast steps after clean = 0
[2026-02-22 11:38:58] [0:00:19:465] [DEF] f:mvp_ptz_self_check l:574
########MRD Lib V1.0.08########
[A/DRV] ak_cam_vidioc_cropcap 1495 input_id:0, chn_id:0
[2026-02-22 11:38:59] [0:00:19:690] [DEF] turn to last pos h:764 v:1180
[2026-02-22 11:38:59] [0:00:19:690] [DEF] == set ptz to position [764, 1180], cur position [1700, 600]==
[A/MOT] [ms32006_motor_move_thread][l:453][idx:1][cur:1700]to set run step 936
[ MD][2026-02-22 04:38:59 040] [md_thread:443] thread id : 0
[ MD][2026-02-22 04:38:59 120] [ak_md_set_sensitivity:691] sensitivity:90
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
[ MD][2026-02-22 04:38:59 130] [ak_md_enable:1076] enable:1
[2026/02/22 11:38:59][0:00:19.825][WRN][alarm][mv_alarm_schedule_filter_flush][ALL DAY MODE]
[_wait_service_ready][timezone:7][s16_time_zone_offset:0]

[server ready]
[2026-02-22 11:38:59] [0:00:19:825] [DEF] [_pth_main_start]init finish
Play Finished, mp3 decoder size:54144
[atbm_log]:AMPDU[0]:action[0],tid[1],ssn[1],buff_size[0],token[1],cc:b2:55:9a:44:16
go out play mp3 file /mnt/mtd/mvsound/sf_connected.mp3 , break_status:0
[A/MOT] clean_motor_steps_fast steps after clean = 0
[2026-02-22 11:39:00] [0:00:21:085] [DEF] now horizon[764]
[A/MOT] [ms32006_motor_move_thread][l:453][idx:0][cur:600]to set run step 580
[2026/02/22 11:39:00][0:00:21.405][INF][mvscomm]to set time cause cur->net [1771735140 / 1771735143]
[2026/02/22 11:39:00][0:00:21.405][INF][mvscomm]evt MVSPT_EVENT_SYSTIME_UPDATED call
systime updated event standard:1771735143 device:1771735140
[2026/02/22 11:39:01][0:00:21.715][INF][mvsudip]Logon success! Using P2P Svr [0]
[2026/02/22 11:39:01][0:00:21.715][INF][mvscomm]evt MVSPT_EVENT_IOTC_CONNECTED call
mvspt_event_handler[354] IOTC_CONNECTED
[2026/02/22 11:39:01][0:00:21.765][WRN][mvscsp][TCP]Recv failed, retcode=[-24], errno=[104]
[2026/02/22 11:39:01][0:00:21.765][WRN][mvscsp][_key_exchange][l:434]exp ocr (-24) at l:432; msg:""
[2026/02/22 11:39:01][0:00:21.795][WRN][mvscomm][_iotc_dprops_push_body_fill][l:196]get dpid [65792] not support, skip!
[A/MOT] clean_motor_steps_fast steps after clean = 0
[2026-02-22 11:39:01] [0:00:21:995] [DEF] now vertical[1180]
[2026/02/22 11:39:01][0:00:22.000][WRN][ptz][_pth_ptz_cruise_start]ready
[2026-02-22 11:39:01] [0:00:22:000] [DEF] === start mv_recorder ptz_pos ===
[2026-02-22 11:39:01] [0:00:22:000] [DEF] === need to record cur postion h:764 v1180===
[2026-02-22 11:39:01] [0:00:22:015] [DEF] ptz init finish
[2026/02/22 11:39:01][0:00:22.225][INF][mvsudip]p2p ver upload success!!
[2026/02/22 11:39:01][0:00:22.230][INF][mvsudip]p2p ver upload fin.
[2026/02/22 11:39:01][0:00:22.445][INF][mvsota]no available update : -1003
[2026/02/22 11:39:03][0:00:24.360][WRN][mvscomm][com_http_auth_do][l:95]com http do failed -2
[2026/02/22 11:39:03][0:00:24.360][WRN][mvsmqtt][_pull_license_with_http][l:313]exp ocr (-24) at l:310; msg:"res:-2,code:0"
[2026/02/22 11:39:08][0:00:29.100][WRN][mvscomm][TCP]Connect poll failed !!
[2026/02/22 11:39:08][0:00:29.100][WRN][mvscomm][TCP]Connect [8.138.251.228:443] failed !!
[2026/02/22 11:39:08][0:00:29.100][WRN][mvscomm][TCP]Connect poll failed !!
[2026/02/22 11:39:08][0:00:29.100][WRN][mvscomm][TCP]Connect [8.138.251.228:443] failed !!
[atbm_log]:AMPDU[0]:action[0],tid[5],ssn[1],buff_size[0],token[2],cc:b2:55:9a:44:16
[2026/02/22 11:39:13][0:00:33.995][INF][mvscss]new vip permission: [0]
[2026/02/22 11:39:13][0:00:33.995][INF][mvscss]new service type: [0]
[2026/02/22 11:39:13][0:00:34.260][INF][mvscss]new vip permission: [0]
[2026/02/22 11:39:13][0:00:34.260][INF][mvscss]new service type: [0]
[atbm_log]:AMPDU[0]:action[1],tid[1],ssn[0],buff_size[0],token[1],cc:b2:55:9a:44:16
[2026/02/22 11:39:15][0:00:36.405][WRN][mvscomm][com_http_auth_do][l:95]com http do failed -2
[2026/02/22 11:39:15][0:00:36.405][WRN][mvsmqtt][_pull_license_with_http][l:313]exp ocr (-24) at l:310; msg:"res:-2,code:0"

Password:

Enjoy!

(ash:/)# [atbm_log]:AMPDU[0]:action[1],tid[1],ssn[0],buff_size[0],token[1],cc:b2:55:9a:44:16

(ash:/)#

Командой telnetcli запускаю telnet

telnet server started, port is 4322

Получаюсь по телнету на порт 4322

---

Debug Message
Message: [TELNET] Telnet Server Connected. Welcome.

        Welcome to AliOS Things

(ash:/)#

Даю команду

(ash:/)# /mnt/sdcard/setup.sh
(ash:/)#

В ответ ничего, новая строка.

[kamyaruk]

Сдампил флэшку.

P25Q32H@SOP8-200_20260222_150143_camera_v380pro.zip

[Arkady23]

Командой telnetcli запускаю telnet
telnet server started, port is 4322
Получаюсь по телнету на порт 4322

---

Супер. Если есть телнет. Надо сначала разобраться, чтобы не накосячить. Я сначала смотрю на ПО. Всё можно заархивировать. И вам этот архив пригодится. Использую такие команды:

tar -cvpf /mnt/sdcard/linux_bin.tar  /bin/
tar -cvpf /mnt/sdcard/linux_etc.tar  /etc/
tar -cvpf /mnt/sdcard/linux_mnt.tar  /mnt/
tar -cvpf /mnt/sdcard/linux_mvs.tar  /mvs/
tar -cvpf /mnt/sdcard/linux_sbin.tar  /sbin/
tar -cvpf /mnt/sdcard/linux_tmp.tar  /tmp/
tar -cvpf /mnt/sdcard/linux_usr.tar  /usr/

Самая интересна папка это /mvs/. Скрипт setup.sh уже прописал загрузку стартового файла с sd /mnt/sdcard/ark-add-on/startup.sh.
Но дело в том, что в новых камерах производители уже ставят защиту от запуска этого файла. Поэтому есть новая версия setup.sh. Но т.к. вы уже запустили, то надо разобраться работает ли /mnt/sdcard/ark-add-on/startup.sh. Запускает ли он ftp, telnet и http при старте камеры. Если точно не запускает, т.е. он не стартует, тогда надо переходить к новому установщику. Если сможете заархивировать эти папки — пришлите на a@kornienko.ru.

[Arkady23]

А avi-файлы и каталоги с ними на sd-карте создаются? Где-то же там должно быть их ПО? Как-то надо попробовать без tar скопировать всё, весь Linux на sd. Может быть командой cp?

[kamyaruk]

Видеофайлы складываются в корне карты памяти в папке MVRec01, например
MVRec01\202602\22\10\1356.mvr
MVRec01\202602\22\15\2755.mvr

[Arkady23]

Ого! Это принципиально новое ПО. Поэтому мой web-сервер сегодняшней версии туда точно не подойдёт. Это надо иметь камеру такого типа или хотя бы копию Linux, чтобы начать что-то дорабатывать.

[kamyaruk]

Командой cp -r не дает, система падает в panic и перезагружается.
Внутри дампа есть строки:

/mnt/sdcard/updatepatch [PATCH_UPDATE][ERR]error === patch not exists in sdcard ===
...

/mnt/sdcard/patch_reuse [PATCH_UPDATE][DBG]update content: [%d], flag[%d]

...

/mnt/sdcard/ftool.j /mnt/sdcard/ [f:%s][module type:%d][cur mode:%d]

[Arkady23]

Я нашел в чем причина. Через пару часов заменю библиотеки, это папки /mnt/sdcard/bin/ и /mnt/sdcard/cgi-bin/ также ван нужно будет убедиться, что в корне sd есть файл index.html.gz.